 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| a FEATURES Low Cost Low Power: 1.15 mA Max for 5 V Supply High Speed 400 MHz, -3 dB Bandwidth (G = +1) 4000 V/ s Slew Rate 60 ns Overload Recovery Fast Settling Time of 24 ns Drive Video Signals on 50 Lines Very Low Noise 3.5 nV/Hz and 5 pA/Hz 5 nV/Hz Total Input Referred Noise @ G = +3 w/500 Feedback Resistor Operates on +4.5 V to +12 V Supplies Low Distortion -70 dB THD @ 5 MHz Low, Temperature-Stable DC Offset Available in SOIC-8 and SOT-23-5 APPLICATIONS Photo-Diode Preamp Professional and Portable Cameras Hand Sets DVD/CD Handheld Instruments A-to-D Driver Any Power-Sensitive High Speed System PRODUCT DESCRIPTION 400 MHz Low Power High Performance Amplifier AD8014 FUNCTIONAL BLOCK DIAGRAMS SOIC-8 (R) SOT-23-5 (RT) 8 NC 7 +VS 6 VOUT VOUT 1 -VS 2 +IN 3 4 NC 1 -IN 2 AD8014 5 +VS +IN 3 -VS 4 AD8014 5 NC -IN NC = NO CONNECT The AD8014 is a very high speed amplifier with 400 MHz, -3 dB bandwidth, 4000 V/s slew rate, and 24 ns settling time. The AD8014 is a very stable and easy to use amplifier with fast overload recovery. The AD8014 has extremely low voltage and current noise, as well as low distortion, making it ideal for use in wide-band signal processing applications. For a current feedback amplifier, the AD8014 has extremely low offset voltage and input bias specifications as well as low drift. The input bias current into either input is less than 15 A at +25C with a typical drift of less than 50 nA/C over the industrial temperature range. The offset voltage is 5 mV max with a typical drift less than 10 V/C. For a low power amplifier, the AD8014 has very good drive capability with the ability to drive 2 V p-p video signals on 75 or 50 series terminated lines and still maintain more than 135 MHz, 3 dB bandwidth. The AD8014 is a revolutionary current feedback operational amplifier that attains new levels of combined bandwidth, power, output drive and distortion. Analog Devices, Inc. uses a proprietary circuit architecture to enable the highest performance amplifier at the lowest power. Not only is it technically superior, but is low priced, for use in consumer electronics. This general purpose amplifier is ideal for a wide variety of applications including battery operated equipment. REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 1999 AD8014-SPECIFICATIONS (@ T = +25 C, V = A S 5 V, RL = 150 , RF = 1 k , Gain = +2, unless otherwise noted) AD8014AR/RT Min Typ Max 400 120 140 170 480 160 180 210 130 12 20 4600 2800 4000 2500 24 1.6 2.8 60 -68 -51 -45 -48 3.5 5 0.05 0.46 0.30 0.60 22 2 2 10 5 50 5 1300 450 2.3 4.1 -57 3.8 4.0 50 70 40 5 1.15 -58 6.0 1.3 5 6 15 Units MHz MHz MHz MHz MHz MHz MHz V/s V/s V/s V/s ns ns ns ns dB dB dB dB nV/Hz pA/Hz % % Degree Degree dBm mV mV V/C A nA/C A k k pF V dB V V mA mA pF V mA dB Parameter DYNAMIC PERFORMANCE -3 dB Bandwidth Small Signal -3 dB Bandwidth Large Signal Conditions G = +1, VO = 0.2 V p-p, RL = 1 k G = -1, VO = 0.2 V p-p, RL = 1 k VO = 2 V p-p VO = 2 V p-p, RF = 500 VO = 2 V p-p, RF = 500 , RL = 50 VO = 0.2 V p-p, RL = 1 k VO = 2 V p-p, RL = 1 k RL = 1 k, RF = 500 RL = 1 k G = -1, RL = 1 k, RF = 500 G = -1, RL = 1 k G = +1, VO = 2 V Step, R L = 1 k 2 V Step G = -1, 2 V Step 0 V to 4 V Step at Input fC = 5 MHz, VO = 2 V p-p, RL = 1 k fC = 5 MHz, VO = 2 V p-p fC = 20 MHz, VO = 2 V p-p fC = 20 MHz, VO = 2 V p-p f = 10 kHz f = 10 kHz NTSC, G = +2, RF = 500 NTSC, G = +2, RF = 500 , RL = 50 NTSC, G = +2, RF = 500 NTSC, G = +2, RF = 500 , RL = 50 f = 10 MHz 0.1 dB Small Signal Bandwidth 0.1 dB Large Signal Bandwidth Slew Rate, 25% to 75%, VO = 4 V Step Settling Time to 0.1% Rise and Fall Time 10% to 90% Overload Recovery to Within 100 mV NOISE/HARMONIC PERFORMANCE Total Harmonic Distortion SFDR Input Voltage Noise Input Current Noise Differential Gain Error Differential Phase Error Third Order Intercept DC PERFORMANCE Input Offset Voltage TMIN-TMAX Input Offset Voltage Drift Input Bias Current Input Bias Current Drift Input Offset Current Open Loop Transresistance INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Short Circuit Current Capacitive Load Drive for 30% Overshoot POWER SUPPLY Operating Range Quiescent Current Power Supply Rejection Ratio Specifications subject to change without notice. +Input or -Input 800 +Input +Input VCM = 2.5 V RL = 150 RL = 1 k VO = 2.0 V 2 V p-p, RL = 1 k, RF = 500 2.25 4 V to 6 V -55 3.8 -52 3.4 3.6 40 -2- REV. B SPECIFICATIONS (@ T = +25 C, V = +5 V, R = 150 A S L AD8014 , RF = 1 k , Gain = +2, unless otherwise noted) Min 345 100 75 90 AD8014AR/RT Typ Max 430 135 100 115 100 10 20 3900 1100 1800 1100 24 1.9 2.8 60 -70 -51 -45 -47 3.5 5 0.06 0.05 0.03 0.30 22 2 2 10 5 50 5 1300 450 2.3 1.1 to 3.9 -57 1.1 to 3.9 0.9 to 4.1 50 70 55 5 1.0 -58 5 6 15 Units MHz MHz MHz MHz MHz MHz MHz V/s V/s V/s V/s ns ns ns ns dB dB dB dB nV/Hz pA/Hz % % Degree Degree dBm mV mV V/C A nA/C A k k pF V dB V V mA mA pF V mA dB Parameter DYNAMIC PERFORMANCE -3 dB Bandwidth Small Signal -3 dB Bandwidth Large Signal Conditions G = +1, VO = 0.2 V p-p, RL = 1 k G = -1, VO = 0.2 V p-p, RL = 1 k VO = 2 V p-p VO = 2 V p-p, RF = 500 VO = 2 V p-p, RF = 500 , RL = 75 VO = 0.2 V p-p, RL = 1 k VO = 2 V p-p RL = 1 k, RF = 500 RL = 1 k G = -1, RL = 1 k, RF = 500 G = -1, RL = 1 k G = +1, VO = 2 V Step, RF = 1 k 2 V Step G = -1, 2 V Step 0 V to 2 V Step at Input fC = 5 MHz, VO = 2 V p-p, RL = 1 k fC = 5 MHz, VO = 2 V p-p fC = 20 MHz, VO = 2 V p-p fC = 20 MHz, VO = 2 V p-p f = 10 kHz f = 10 kHz NTSC, G = +2, RF = 500 NTSC, G = +2, RF = 500 , RL = 50 NTSC, G = +2, RF = 500 NTSC, G = +2, RF = 500 , RL = 50 f = 10 MHz 0.1 dB Small Signal Bandwidth 0.1 dB Large Signal Bandwidth Slew Rate, 25% to 75%, VO = 2 V Step Settling Time to 0.1% Rise and Fall Time 10% to 90% Overload Recovery to Within 100 mV NOISE/HARMONIC PERFORMANCE Total Harmonic Distortion SFDR Input Voltage Noise Input Current Noise Differential Gain Error Differential Phase Error Third Order Intercept DC PERFORMANCE Input Offset Voltage TMIN-TMAX Input Offset Voltage Drift Input Bias Current Input Bias Current Drift Input Offset Current Open Loop Transresistance INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Short Circuit Current Capacitive Load Drive for 30% Overshoot POWER SUPPLY Operating Range Quiescent Current Power Supply Rejection Ratio Specifications subject to change without notice. +Input or -Input 750 +Input +Input VCM = 1.5 V to 3.5 V RL = 150 to 2.5 V RL = 1 k to 2.5 V VO = 1.5 V to 3.5 V 2 V p-p, RL = 1 k, RF = 500 4.5 4 V to 5.5 V -55 1.2 -52 1.4 1.2 30 3.8 3.6 3.8 12 1.15 REV. B -3- AD8014 ABSOLUTE MAXIMUM RATINGS 1 Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12.6 V Internal Power Dissipation2 Small Outline Package (R) . . . . . . . . . . . . . . . . . . . . 0.75 W SOT-23-5 Package (RT) . . . . . . . . . . . . . . . . . . . . . . 0.5 W Input Voltage Common Mode . . . . . . . . . . . . . . . . . . . . . . VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . 2.5 V Output Short Circuit Duration . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves Storage Temperature Range . . . . . . . . . . . . -65C to +150C Operating Temperature Range . . . . . . . . . . . -40C to +85C Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . .+300C ESD (Human Body Model) . . . . . . . . . . . . . . . . . . . . +1500 V NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these or any other conditions above listed in the operational section of this specification is not implied. Exposure to Absolute Maximum Ratings for any extended periods may affect device reliability. 2 Specification is for device in free air at 25C. 8-Lead SOIC Package JA = 155C/W. 5-Lead SOT-23 Package JA = 240C/W. plastic. This is approximately +150C. Even temporarily exceeding this limit may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175C may result in device failure. The output stage of the AD8014 is designed for large load current capability. As a result, shorting the output to ground or to power supply sources may result in a very large power dissipation. To ensure proper operation it is necessary to observe the maximum power derating tables. Table I. Maximum Power Dissipation vs. Temperature Ambient Temp C -40 -20 0 +20 +40 +60 +80 +100 Power Watts SOT-23-5 0.79 0.71 0.63 0.54 0.46 0.38 0.29 0.21 Power Watts SOIC 1.19 1.06 0.94 0.81 0.69 0.56 0.44 0.31 MAXIMUM POWER DISSIPATION The maximum power that can be safely dissipated by the AD8014 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the ORDERING GUIDE Model AD8014AR AD8014ART2 AD8014AChips3 1 Temperature Range -40C to +85C -40C to +85C -40C to +85C Package Descriptions 8-Lead SOIC 5-Lead SOT-23 Not Applicable Package Options SO-8 RT-5 Waffle Pak Brand Code Standard HAA Not Applicable NOTES 1 The AD8014AR is also available in 13" Reels of 2500 each and 7" Reels of 750 each. 2 Except for samples, the AD8014ART is only available in 7" Reels of 3000 each and 13" Reels of 10000 each. 3 The AD8014A Chips are available only in Waffle Pak of 400 each. The thickness of the AD8014A Chip is 12 mils 1 mil. The Substrate should be tied to the +V S source. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8014 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE -4- REV. B Typical Performance Characteristics- AD8014 15 12 9 NORMALIZED GAIN - dB 6 3 VS = +5V 0 -3 -6 -9 -12 -15 G = +1 VO = 200mV p-p RF = 1k RL = 1k VS = 5V NORMALIZED GAIN - dB 2.0 1.0 VO = 0.2V 0 VO = 0.5V -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 1 10 100 FREQUENCY - MHz 1000 -7.0 1 10 100 FREQUENCY - MHz 1000 VS = 5V G = -1 RF = 1k RL = 1k VO = 1V VO = 2V VO = 4V Figure 1. Frequency Response, G = +1, VS = 5 V and +5 V Figure 4. Bandwidth vs. Output Level--Gain of -1, Dual Supply 12 9 6 NORMALIZED GAIN - dB 3 0 -3 -6 -9 -12 -15 1 10 100 FREQUENCY - MHz 1000 VS = 5V G = +2 RF = 500 VO = 2V p-p RL = 50 RL = 75 NORMALIZED GAIN - dB 12 9 VO = 0.5V p-p 6 3 0 -3 -6 -9 -12 1 10 100 FREQUENCY - MHz 1000 VS = +5V G = +2 RF = 1k RL = 1k VO = 3V p-p VO = 2V p-p VO = 1V p-p Figure 2. Frequency Response, G = +2, VO = 2 V p-p Figure 5. Bandwidth vs. Output Level--Single Supply, G = +2 12 9 NORMALIZED GAIN - dB 6 3 0 -3 VO = 2V p-p -6 -9 -12 10 100 FREQUENCY - MHz 1000 VS = 5V G = +2 RF = 1k RL = 1k VO = 4V p-p VO = 0.5V p-p NORMALIZED GAIN - dB VO = 1V p-p 2 1 VO = 0.5V p-p 0 -1 -2 -3 -4 -5 -6 -7 -8 1 10 100 FREQUENCY - MHz 1000 VS = +5V G = -1 RF = 1k RL = 1k VO = 0.2V p-p VO = 4V p-p VO = 2V p-p Figure 3. Bandwidth vs. Output Voltage Level-- Dual Supply, G = +2 Figure 6. Bandwidth vs. Output Level--Single Supply, Gain of -1 REV. B -5- AD8014 7.5 7.0 6.5 NORMALIZED GAIN - dB 6.0 5.5 5.0 4.5 4.0 3.5 3.0 1 10 100 FREQUENCY - MHz 1000 VS = 5V RF = 1k G = +2 VO = 2V p-p RL = 150 RF = 750 RF = 300 RF = 500 GAIN FLATNESS - dB RF = 600 6.2 6.1 VS = 6.0 5.9 5.8 5.7 5.6 5.5 5.4 5.3 5.2 1 10 100 FREQUENCY - MHz 1000 G = +2 V = 2V p-p RF = 500 RL = 150 VS = +5V 5V Figure 7. Bandwidth vs. Feedback Resistor--Dual Supply Figure 10. Gain Flatness--Large Signal 7.5 7.0 NORMALIZED GAIN - dB 9 6 3 G = +1 6.5 RF = 300 6.0 RF = 500 5.5 RF = 750 5.0 VS = +5V G = +2 VO = 2V p-p RL = 150 4.0 1 10 100 FREQUENCY - MHz 1000 RF = 1k GAIN - dB 0 G = +2 -3 -6 G = +10 -9 -12 -15 -18 1 10 100 FREQUENCY - MHz 1000 VS = 5V RF = 1k RL = 1k VO = 200mV p-p 4.5 Figure 8. Bandwidth vs. Feedback Resistor--Single Supply Figure 11. Bandwidth vs. Gain--Dual Supply, RF = 1 k 6.8 6.7 6.6 NORMALIZED GAIN - dB 6.5 6.4 6.3 6.2 6.1 6.0 5.9 5.8 5.7 5.6 1 10 100 FREQUENCY - MHz 1000 VS = +5V GAIN - dB G = +2 RF = 1k RL = 1k VO = 200mV p-p VS = 5V 9 6 3 0 -3 -6 -9 -12 -15 -18 1 10 100 FREQUENCY - MHz 1000 VS = +5V RF = 1k RL = 1k VO = 200mV p-p G = +10 G = +2 G = +1 Figure 9. Gain Flatness--Small Signal Figure 12. Bandwidth vs. Gain--Single Supply -6- REV. B AD8014 0 -10 -20 -30 PSRR - dB -40 -50 -60 -70 -80 -90 -100 0.01 0.10 1 10 FREQUENCY - MHz 100 1000 0 1k 10k 100k 1M 10M FREQUENCY - Hz 100M -280 1G 140 120 100 PHASE 0 -40 -80 -120 GAIN -160 -200 -240 VS = 5V -PSRR 80 60 40 20 +PSRR Figure 13. PSRR vs. Frequency Figure 16. Transimpedance Gain and Phase vs. Frequency -20 -25 -30 OUTPUT RESISTANCE - -35 CMRR - dB -40 -45 -50 -55 -60 -65 -70 -75 0.1 VS = 5V VS = +5V 100 10 1 0.1 0.01 0.01 1 10 FREQUENCY - MHz 100 1000 0.1 1 10 FREQUENCY - MHz 100 1000 Figure 14. CMRR vs. Frequency Figure 17. Output Resistance vs. Frequency, VS = 5 V and +5 V -30 3RD RL = 150 DISTORTION - dBc -50 2ND RL = 150 2ND RL = 1k -70 3RD RL = 1k DISTORTION BELOW NOISE FLOOR -90 1 10 FREQUENCY - MHz 100 Figure 15. Distortion vs. Frequency; VS = 5 V, G = +2 Figure 18. Settling Time REV. B -7- PHASE - Degrees G = +2 RF = 1k GAIN - dB AD8014 Figure 21 shows the circuit that was used to imitate a photodiode preamp. A photodiode for this application is basically a high impedance current source that is shunted by a small capacitance. In this case, a high voltage pulse from a Picosecond Pulse Labs Generator that is ac-coupled through a 20 k resistor is used to simulate the high impedance current source of a photodiode. This circuit will convert the input voltage pulse into a small charge package that is converted back to a voltage by the AD8014 and the feedback resistor. In this case the feedback resistor chosen was 1.74 k, which is a compromise between maintaining bandwidth and providing sufficient gain in the preamp stage. The circuit preserves the pulse shape very well with very fast rise time and a minimum of overshoot as shown in Figure 22. 1.74k +5V 0.1 F INPUT 20k 49.9 49.9 Figure 19. Large Signal Step Response; V S = 5 V, VO = 4 V Step AD8014 OUTPUT (10 PROBE) (NO LOAD) -5V Figure 21. AD8014 as a Photodiode Preamp TEK RUN: 2.0GS/s ET AVERAGE T[ ] INPUT 1 20mV/DIV Figure 20. Large Signal Step Response; V S = +5 V, VO = 2 V Step Note: On Figures 19 and 20 RF = 500 , R S = 50 and C L = 20 pF. APPLICATIONS CD ROM and DVD Photodiode Preamp OUTPUT 2 500mV/DIV CH1 20.0V CH2 500mV M 25.0ns CH4 380mV Figure 22. Pulse Response High speed Multi-X CD ROM and DVD drives require high frequency photodiode preamps for their read channels. To minimize the effects of the photodiode capacitance, the low impedance of the inverting input of a current feedback amplifier is advantageous. Good group delay characteristics will preserve the pulse response of these pulses. The AD8014, having many advantages, can make an excellent low cost, low noise, low power, and high bandwidth photodiode preamp for these applications. -8- REV. B AD8014 Video Drivers DRIVING CAPACITIVE LOADS The AD8014 easily drives series terminated cables with video signals. Because the AD8014 has such good output drive you can parallel two or three cables driven from the same AD8014. Figure 23 shows the differential gain and phase driving one video cable. Figure 24 shows the differential gain and phase driving two video cables. Figure 25 shows the differential gain and phase driving three video cables. DIFFERENTIAL PHASE - Degrees DIFFERENTIAL GAIN - % 0.00 0.02 0.04 0.05 0.05 0.05 0.04 0.04 0.04 0.04 0.03 The AD8014 was designed primarily to drive nonreactive loads. If driving loads with a capacitive component is desired, best settling response is obtained by the addition of a small series resistance as shown in Figure 26. The accompanying graph shows the optimum value for RSERIES vs. Capacitive Load. It is worth noting that the frequency response of the circuit when driving large capacitive loads will be dominated by the passive roll-off of RSERIES and CL. 40 0.10 0.05 0.00 -0.05 -0.10 0.60 0.40 0.20 0.00 -0.20 -0.40 -0.60 30 RSERIES - 20 10 0.00 0.01 0.10 0.21 0.26 0.28 0.29 0.30 0.30 0.30 0.30 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH Figure 23. Differential Gain and Phase R F = 500, 5 V, RL = 150 , Driving One Cable, G = +2 DIFFERENTIAL PHASE - Degrees DIFFERENTIAL GAIN - % 0.00 -0.02 0.03 0.05 0.06 0.06 0.05 0.05 0.07 0.10 0.14 0 5 10 CL - pF 15 20 25 Figure 26. Driving Capacitive Load Choosing Feedback Resistors 0.30 0.20 0.10 0.00 -0.10 -0.20 -0.30 0.60 0.40 0.20 0.00 -0.20 -0.40 -0.60 Changing the feedback resistor can change the performance of the AD8014 like any current feedback op amp. The table below illustrates common values of the feedback resistor and the performance which results. 0.00 0.07 0.24 0.40 0.43 0.44 0.43 0.40 0.35 0.26 0.16 Table II. 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH Gain +1 +2 +10 -1 -2 -10 +2 +2 +2 RF 1 k 1 k 1 k 1 k 1 k 1 k 2 k 750 499 RG Open 1 k 111 1 k 499 100 2 k 750 499 -3 dB BW VO = 0.2 V RL = 1 k 480 280 50 160 140 45 200* 260* 280* -3 dB BW VO = 0.2 V RL = 150 430 260 45 150 130 40 180* 210* 230* Figure 24. Differential Gain and Phase R F = 500, 5 V, RL = 75 , Driving Two Cables, G = +2 DIFFERENTIAL PHASE - Degrees DIFFERENTIAL GAIN - % 0.00 0.44 0.52 0.54 0.52 0.52 0.50 0.48 0.47 0.44 0.45 0.80 0.60 0.40 0.20 0.00 -0.20 -0.40 -0.60 -0.80 0.80 0.60 0.40 0.20 0.00 -0.20 -0.40 -0.60 -0.80 0.00 0.10 0.32 0.53 0.57 0.59 0.58 0.56 0.54 0.51 0.48 *VO = 1 V. 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH Figure 25. Differential Gain and Phase R F = 500, 5 V, RL = 50 , Driving Three Cables, G = +2 REV. B -9- AD8014 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Lead Plastic SOIC (SO-8) C3439b-0-12/99 0.0196 (0.50) x 45 0.0099 (0.25) 8 0 0.0500 (1.27) 0.0160 (0.41) 0.0079 (0.20) 0.0031 (0.08) 10 0 0.0217 (0.55) 0.0138 (0.35) 0.1968 (5.00) 0.1890 (4.80) 8 1 5 4 0.1574 (4.00) 0.1497 (3.80) 0.2440 (6.20) 0.2284 (5.80) PIN 1 0.0098 (0.25) 0.0040 (0.10) 0.0688 (1.75) 0.0532 (1.35) 0.0500 0.0192 (0.49) SEATING (1.27) 0.0098 (0.25) PLANE BSC 0.0138 (0.35) 0.0075 (0.19) 5-Lead Plastic Surface Mount (SOT-23) (RT-5) 0.1181 (3.00) 0.1102 (2.80) 0.0669 (1.70) 0.0590 (1.50) PIN 1 5 1 2 4 3 0.1181 (3.00) 0.1024 (2.60) 0.0374 (0.95) BSC 0.0748 (1.90) BSC 0.0512 (1.30) 0.0354 (0.90) 0.0059 (0.15) 0.0019 (0.05) 0.0197 (0.50) 0.0138 (0.35) 0.0571 (1.45) 0.0374 (0.95) SEATING PLANE -10- REV. B PRINTED IN U.S.A. |
Price & Availability of AD8014
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |